{"product_id":"holybro-pm06d-power-module-2-14s-for-pixhawk-5x-pixhawk-6x-flight-controller-diy-parts","title":"HolyBro PM06D Power Module 14S","description":"\u003cp\u003eThis PM uses I2C digital signal data output, only compatible with Pixhawk 5X\/6X series.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003cspan style=\"text-decoration: underline;\"\u003eNote\u003c\/span\u003e\u003cbr\u003e\u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e- PM06D is supported by PX4. For Ardupilot, it is supported in version 4.4 and later. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"color: #ff2a00;\"\u003e- This PM uses I2C digital signal data output and is not compatible with flight controller that uses analog PM such as the Pixhawk 6C \u0026amp; Mini, Pixhawk4 \u0026amp; Mini, pix32 v5, or Durandal flight controllers.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003ePM06D provides regulated power supply for your Pixhawk® 5X \u0026amp; 6X from the \u003ca\u003ebattery,\u003c\/a\u003e\u003ca\u003e \u003c\/a\u003eas well as current consumption and battery voltage measurements, all through a 6pin cable. It has built-in power distribution, allowing you power your ESC and FC with the same board.\u003cbr\u003e\u003cbr\u003eThe on-board switching regulator outputs 5.2V and a maximum of 3A from LiPo batteries up to 14S. The Power Module comes completely assembled with a XT60 connector and a capacitor. The Molex 2.00mm pitch CLIK-Mate Wire-to-Board connector is rated for 3.0A current per contact.\u003c\/p\u003e\n\u003cp\u003eSpecification\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eInput voltage: 2S- 14S\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePCB Cont. Current Rating: 70A\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePCB Burst Current Rating: 120A (\u0026lt;60 Sec)\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eMax current sensing: 327A\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eVoltage and current monitor with I2C compatible interface \u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eConnector Outputs: 5.2V and 3A max \u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eWeight: 24.5g\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eCurrent Rating:\u003c\/p\u003e\n\u003cp\u003eThe PM06D comes with XT60 plugs with 14 AWG silicone wires rated for 30A continuous current and 60A burst current (\u0026lt;1 minute). If a higher current is needed, the plug type and wire size should be changed accordingly. You can refer to \u003ca href=\"https:\/\/docs.holybro.com\/power-module-and-pdb\/power-module\/connector-and-wire-rating\"\u003ethis chart \u003c\/a\u003eas reference.\u003c\/p\u003e\n\u003cp\u003ePX4 Parameter Setup:\u003c\/p\u003e\n\u003cp\u003eIf you are using the PM06D 14S version, you must set \u003cem\u003eSENS_EN_INA228 \u003c\/em\u003eto enable\u003cem\u003e.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003ePackage Includes：\u003c\/p\u003e\n\u003cp\u003e1x  PM06D Power Module\u003c\/p\u003e\n\u003cp\u003e1x  6pin 2.00mm pitch cable\u003c\/p\u003e","brand":"Holybro","offers":[{"title":"Default Title","offer_id":54760891187566,"sku":"ACP0078","price":33.29,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1000\/9188\/7982\/files\/15020-4-1800x1800-webp.jpg?v=1789067569","url":"https:\/\/drone-motor.com\/products\/holybro-pm06d-power-module-2-14s-for-pixhawk-5x-pixhawk-6x-flight-controller-diy-parts","provider":"drone motor","version":"1.0","type":"link"}