holybro

The Holybro Digital Airspeed Sensor has a very low offset, a high resolution, and best of all, does not suffer from the noise induced by long cables and offsets in the ratio-metric output on other airspeed sensors. Supported on all Holybro Flight Controller Boards...

Feature Supports 2-14S & 200A Cont, 400A Burst DroneCAN Communication Protocol Small & Compact Design  Two 5V Output with Independent BEC IC and Circuitry Separated Sensor and BEC Board to Minimize Electrical Noise Interference Galvanically Isolated Current Sensor IC (AEC-Q100 Grade 1 qualified) High...

Overview The Holybro H-Flow is a compact optical flow and distance sensor module that combines a PixArt PAA3905E1 optical flow sensor, a Broadcom AFBR-S50LV85D distance sensor, and an InvenSense ICM-42688-P 6-axis IMU. This all-in-one design simplifies installation, while the onboard infrared LED enhances visibility in...

Overview The Holybro UM982 Dual Antenna RTK GPS provides high-precision positioning information and is capable of generating non-magnetometer moving baseline yaw determinations for autopilots with one single GPS module.  One of the best applications of this GPS is to provide compass-less YAW information to...

Overview The M10 GPS uses multi-constellation GNSS powered by u-blox M10 series, a concurrent GNSS receiver which can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS,Galileo, GLONASS and BeiDou can be received concurrently.It also comes with...

The M9N/M10 V2 GPS uses multi-constellation GNSS powered by u-blox M9N/M10, a concurrent GNSS receiver that can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture, all four major GNSS constellations, GPS, Galileo, GLONASS, and BeiDou, can be received concurrently. The V2 design...

VTX & OSD Specifications: ATmega328P with Arduino bootloader MAX7456 monochrome on-screen display Standard 6-pin ISP header Solder jumper for PAL video option Exposed test points for HSYNC and LOS Dimensions:17.5*35mm Weight:3g Note:BAT+ is direcrly connected with VTx and Camera (Pay attention to the max with stand voltage of your equipment) PIN MAP Diagram Included: Micro OSD * 1GH 6P cable *...

Key Design Points Redundancy: 3x ICM-45686 IMU sensors (±32g) with BalancedGyro™ technology & 2x Barometer sensors High-performance STM32H753 Processor with a clock speed of up to 480 MHz Modular flight controller: separated IMU, FMU, and Base system connected by a 100-pin & a 50-pin Pixhawk®...

Description:This PM02 Power Module provides a simple way to supply regulated 5.2V to flight controller from the battery while providing current consumption and battery voltage measurements via analog signal through a 6 Pin JST-GH cable. It comes with pre-soldered wires, capacitor, and XT60 connector...

This PM uses I2C digital signal data output, only compatible with Pixhawk 5X/6X series. Note PM02D HV version is supported by PX4. For Ardupilot, it is supported in version 4.4 and later. Full setup guide can be found here. This PM uses I2C digital signal data...

Description: This PM06 Power Module supplies clean 5.2V to flight controller from the battery and provides current consumption and battery voltage measurements via analog signal through a 6 Pin JST-GH cable, along with integrated power distribution for 4 ESCs. It comes with pre-soldered wires,...

This PM uses I2C digital signal data output, only compatible with Pixhawk 5X/6X series.   Note- PM06D is supported by PX4. For Ardupilot, it is supported in version 4.4 and later.  - This PM uses I2C digital signal data output and is not compatible with flight...

Description: This Power Distribution Board (PDB) 300A is designed to handle high-current applications, making it ideal for demanding power setups. It is compatible with PM08 series power modules and supports various high-current, multi-output configurations. The board utilizes 10 oz copper, ensuring superior thermal management...

Description: This Power Distribution Board (PDB) 300A is designed to handle high-current applications, making it ideal for demanding power setups. It is compatible with PM08 series power modules and supports various high-current, multi-output configurations. The board utilizes 10 oz copper, ensuring superior thermal management...

Note: Currently shipping REV 8, it has 3x ICM-45686 IMU with BalancedGyro™ Technology, please see this page for the latest firmware support information.PX4 Development Kit - X500 v2 is an affordable, lightweight, and robust carbon fiber professional development drone kit with the latest Holybro Pixhawk 6C or Pixhawk 6X Flight Controller, M8N...

The Holybro S500 V2 Kit is affordable, lightweight, simple, easy to assemble, and no soldering required. This is a complete kit that includes almost everything you need to fly. All you will need is a battery and an RC system (optional). It is perfectly...

This Holybro SiK Long Range Telemetry Radio is a small, light, and inexpensive open-source radio platform with a maximum 50 kilometres range (outdoors, line-of-sight range). This radio is plug-and-play, ready for all Pixhawk Standard and other similar flight controllers, providing the easiest way to...

Tekko32 F4 45A ESC is the latest AM32 ESC from HolyBro. The Tekko32 ESC runs in conjunction with an ARM 32bit compatible F4 MCU. It can run input signals with lower latency, at faster rates, smooths out the RPM band, is capable of both...

Almost Ready-to-Fly (ARF) Kit Feature: New design and minimal assembly time (~15 minutes) Carbon Fiber frame with fiber-reinforced nylon connectors providing easy & straightforward installation Pre-installed motors & ESCs with simple XT30 power plugs for PDB Power distribution board (PDB) with XT60 & XT30 plugs...

Almost Ready-to-Fly (ARF) Kit Feature: Carbon Fiber frame with foldable aluminum arm connector New frame design with minimal assembly time, no soldering required Easy & straightforward installation Spacious platform for easy integration of additional accessories & battery Pre-installed motors, ESCs, and LED with simple...